Search Results

The effects of gasoline fuel properties on exhaust emissions were investigated. Port injection LEVs, a ULEV, a prototype SULEV which were equipped with three–way (3–way) catalysts and also two vehicles with direct injection spark ignition (DISI) engines equipped with NOx storage reduction (NSR) catalysts were tested. Fuel sulfur showed a large effect on exhaust emissions in all the systems. In the case of the DISI engine with the NSR catalyst, NOx conversion efficiency and also regeneration from sulfur poisoning were dramatically improved by reducing sulfur from 30ppm to 8ppm. Distillation properties also affected the HC emissions significantly. The HC emissions increased in both the LEV and the ULEV with a driveability index (DI) higher than about 1150 (deg.F). The ULEV was more sensitive than the LEV. These results show that fuel properties will be important for future technologies required to meet stringent emission regulations.

Influence of sulfur poisoning on NOx storage - reduction catalysts (NSR catalysts) was examined using both model gas and an actual vehicle. Deterioration of NSR catalysts is explained as the balance of sulfate formation in lean operating conditions and the amount of sulfate decomposed under rich operating conditions. This study focused on sulfate decomposition characteristics of NSR catalysts. First, sulfate decomposition characteristics of an NSR catalyst were examined in a model gas test. It was found that the initial temperature of SOx release was higher than the sulfur poisoning temperature. Crystal growth of sulfate by increasing temperature was assumed, and hence suppressed SOx release. Second, various sulfur concentrations (8 - 500 ppm) in gasoline were used for vehicle durability. The duration of one durability cycle was 1,260 seconds, including a 60 second regeneration of sulfur poisoning (AFR 14.2, 700 °C).

In vehicles using a typical heating, ventilating, and air conditioning (HVAC) unit, ventilation loss through the cabin accounts for more than 60% of the heating load. This fact has increasingly important because of the low heat source characteristics of today's increasingly efficient engines. In response to this trend, a new type of air conditioning system, a “Two layer flow HVAC unit”, has been developed. This unit sends low humidity fresh intake air to the window neighborhood in order to promote good demist performance and warm recirculated air to the occupant foot area for increased efficiency. With this system, it is possible to reduce the ventilation loss by half and to raise the cabin temperature by 5°C.

This paper describes a new method for objective evaluation of wind noise in the passenger compartment of a car. The loudness and direction of noise in each frequency band can be estimated by performing analyses based on human hearing properties. Therefore, those wind noise components that are annoying to the passengers or those wind noise components whose source location can be determined by the human listener can be identified objectively. Furthermore, the total loudness of wind noise can be estimated quite precisely by adding the loudness of the frequency bands for noise emanating from the direction of the side window.

As part of the International Lubricant Standardization and Approval Committee's (ILSAC) goal of developing a global automatic transmission fluid (ATF) specification, members have been evaluating test methods that are currently used by various automotive manufacturers for qualifying ATF for use in their respective transmissions. This report deals with comparing test methods used for determining torque capacity in friction systems (shifting clutches). Three test methods were compared, the Plate Friction Test from the General Motors DEXRON®-III Specification, the Friction Durability Test from the Ford MERCON® Specification, and the Japanese Automotive Manufacturers Association Friction Test - JASO Method 348-95. Eight different fluids were evaluated. Friction parameters used in the comparison were breakaway friction, dynamic friction torque at midpoint and the end of engagement, and the ratio of end torque to midpoint torque.

Through a polymer design and precise morphology control, The Super Olefin Polymer, TSOP-1 and TSOP-5 were developed for the material consolidation of interior and exterior parts, respectively. Due to a good balance of TSOP performance, several conventional materials were consolidated into one material for each application. Accordingly, considerable amounts of weight reduction and cost savings have been obtained. In addition to the excellent recyclability of TSOP, the coated bumpers collected from the market were re-utilized through paint decomposition technology. The first dashboard construction, molded partially with foam-padded skin, was also realized. The current amount of TSOP used in a vehicle is about 30% of the total amount of plastic materials. Through the usage of TSOP, 70% of the material consolidation has been achieved.

For energy saving and global warming prevention, Toyota has developed Toyota Hybrid System (THS) for mass-produced passenger cars, which achieves drastic improvement in fuel efficiency and reduction in exhaust emissions compared to conventional gasoline engine cars. The THS has two motive power sources which engage depending on driving conditions. It's power is supplied either from an engine (controlled by the engine ECU) or an electric motor (controlled by the motor ECU) which is powered by a high-voltage battery (monitored by the battery ECU). These ECUs are controlled by a hybrid ECU. Each ECU has been developed with a fail-safe system in mind, to ensure driver safety in case of vehicle breakdowns. Among these ECUs, this paper reports particularly on the newly introduced ECUs: hybrid ECU and battery ECU. In the development of these ECUs, special attention was focused on fail-safe performance.

In order to determine the main factors causing the mileage-related increase in formaldehyde emission from methanol-fueled vehicles, mileage was accumulated on three types of vehicle, each of which had a different air-fuel calibration system. From exhaust emission data obtained during and after the mileage accumulation, it was found that lean burn operation resulted in by far the highest formaldehyde emission increase. An investigation into the reason for the rise in engine-out formaldehyde emission revealed that deposits in the combustion chamber emanating from the lubricating oil promotes formaldehyde formation. Furthermore it was learnt that an increase in engine-out NOx emissions promotes partial oxidation of unburned methanol in the catalyst, leading to a significant increase in catalyst-out formaldehyde emission.

The white smoke generated by a diesel engine was analyzed and found to consist mainly of hydrocarbons. Test results indicated that the emission level depends on ambient temperature. A compact white smoke meter was developed to enable emission levels to be accurately measured. The internal temperature of this meter is controlled so that white smoke is generated within the measuring device. The meter was used to evaluate the effectiveness of various white smoke emission control devices for the DI diesel engine. The results indicated that an intake air heater offers the greatest potential. Accordingly, a new intake air heater with ceramic PTC thermistor having a very high heating efficiency was developed to reduce white smoke emission.

It is well known that pilot injection is an effective method of reducing diesel knock noise during idling, but no actual system has as yet been commercially produced. With the objective of developing a practicable pilot injection device, simulations were conducted of various simple mechanisms in order to determine the best specifications and analyze the fuel injection characteristics. Based on these results, a chamber expansion type pilot injection device, which enables the injection pump pressure chamber volume to be increased at a given moment during the fuel compression stroke, has been developed and has been found to remarkably decrease knock noise during cold idling. An investigation into the effects of this device on output power, exhaust emissions, cold startability and durability revealed that it is eminently suitable for practical application.

The Cathode Ray Tube (CRT) has many superior characteristics compared to other display devices in the area of response, high-resolution, full-color and multi-display capabilities. However, CRTs commonly- used in offices or in the home have not been applicable for automobiles because they could not ensure sufficient display. performance, brightness, vibration resistance, and reliability due to the severe driving conditions of the automobile. We examined the applicability of the CRT into an automobile display system using an experimental vehicle and improved six especially important aspects such as dimensions, display appearance time, effect of magnetism, visibility, stabilization of brightness and prevention of excessive battery drain. Consequently, we developed a new display system called “Toyota Electro Multivision” and introduced it into the ‘85 Toyota Soarer, a luxury class passenger car for the Japanese market only.